Searched for "40140000"
Danfoss -- Wall Mount Operator with Combined Remote Mounted Sensor, Dial and Capillary Tube For Ra2000 Units. Cap Size: 6".
Armstrong factory Circulator Pump Oil. 1/2 Oz. Easy to use. Convenient size makes over oiling a non-issue.
- Factory replacement
- Easy to use tube
- For use on S & H circulators
- Can be used on B and G pumps
- meets factory specifications
- SAE 20
- Detergent free
- Lead free
- Equals B & G L23401
- Lubricates bearing assembly
This non-potable water expansion tank is designed for use in commercial and residential closed loop hydronic heating system piping to control the thermal expansion of hot water and maintain system pressure below the relief setting of the relief valve. This carbon steel tank is pre-charged at 12 PSI, tank volume is 2.1 gallons and features a durable expansion membrane that prevents contact of the water with the air in the tank. This rugged butyl diaphragm minimizes loss of the air change and ensures long and trouble-free life for the system. This tank is made of carbon steel with epoxy finish, mounts to supply piping, 1/2 inch MNPT system connection and a 0.302-32 inch charging valve connection (standard tire valve) to facilitate on-site charging of the tank to meet system requirements. The maximum working pressure is 75 PSI (5.3 BAR).
- Precharged to 12 psi
- Rugged flexible butyl diaphragm
- Inline and free standing models
- Steel construction
This 1/2 in. lead free anti-siphon hot or cold water vacuum breaker prevents the reverse flow of polluted water from entering into the potable water supply due to back siphonage. It consists of polished chrome plated lead free construction, chemical resistant silicone seat disc, chrome hood, and an atmospheric vent to prevent spilling. It has a full size orifice to assure pipe size capacity and maximum flow. It is ideal for low flow, non-continuous hot or cold water health hazard installations such as on laboratory equipment.
- Lead free construction
- Chrome finish
- Female NPT inlet and outlet
- Hot or cold water
- Designed to prevent the backflow of polluted water from entering into the potable water supply
- Ideal for low flow, non-continuous hot or cold water health hazard installations such as on laboratory equipment
- Maximum pressure is 125 psi
The Taco 1-1/4 in. cast iron Freedom Flanges set includes: (2) flanges, (4) nuts, and (4) mounting bolts. These flanges are designed for use with Taco "00", "00e", "2400", and "100" series hydronic circulators. Easily installed and removed with a common wrench.
- For use in a hydronic heating system
- Compatible with a wide variety of Taco circulators
- 1-1/4 in. Dia connection size
- Unique hex design provides easy-on, easy-off installation with a standard adjustable wrench
Long lasting metal fin-tool that straightens and cleans condenser and evaporator fins. Founded in 1971, Diversitech Corporation is North Americas largest manufacturer of equipment pads and a leading manufacturer and supplier of components and related products for multiple industries, including: HVACR, electrical, consumer hardware retail, electrical utility, automotive retail and pool and spa channel. Diversitechs mission for its wholesaler partners is to simplify their work. We do this by offering more than 200 product categories all from a single manufacturing/supplier source to create product availability and supply chain cost advantages for our customers in every market we serve. We also leverage best-in-class customer service to react quickly and professionally to every customer request.
- 1 tool for all units
- Heavy-duty spring wire bristles automatically adjust to all fin spacing's
- Exclusive tension adjustment band is featured to allow maximum rigidity and ease of operation
- Straightens most severely damaged fins
- Stainless steel teeth
- Cushioned red handle to protect your knuckles
- Straightens damaged condenser and evaporator fins quickly and easily
- Increases air conditioner efficiency
- Helps keep air conditioners, condensing units running efficiently
- Works on most air conditioning and refrigeration coils
3-5/32" Centers
- Fits B&G Series 100,PR,NRF-22,NRF-9,NRF-36,PL-36,PL-55 and Armstrong Astro 30 and S-25 Pumps
4- spring Coupler for S & H circulators. Cast iron construction for long service life. Easy cross reference to competing models.
- Cast iron construction
- Couples motor to pump inside bearing assembly housing
- Used on S-25,S-35.H32,H41
- Can used be placed on B & G circulator
- Equals B & G #118705
- Equals B & G #189110
- No balancing required
- No rusting due to construction
- Durable
- Genuine factory replacements
The DELAVAN 0.75 80A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
Features Face Plate, Nut and Washer
- Seal Kit Included
- Fits Bronze Or Iron Body Pumps For Bell & Gossett Or Armstrong
- Replaces Armstrong #816019-02
The DELAVAN 0.85 45B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The Delavan .60 80B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Boiler replacement part
- For use with an oil-burning appliance
- Brass body
- Stainless-steel, solid orifice
All the features you trust from the original Isolator Uni-Flange ball valve, plus a 360 degree rotating flange that allows for orientation to any degree necessary for your installation. This forged brass full port ball valve features a blow-out proof stem, adjustable packing glands and a stainless steel snap ring for extra stability during installation. The only way to isolate circulator pumps.
- Conical inlet to minimize turbulence
- Replaces 3-components, eliminates 2-leak paths, saves approximately 20 minutes in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents electrolysis
- Eliminates galvanic corrosion
Bell & Gossett Bearing Assembly
- Includes Body Gasket and Oil Tube
The DELAVAN 0.85 60A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
Body gasket for use on the Armstrong S and H circulators. Genuine factory replacement. Long lasting and matched to fit Armstrong and competing models.
- 3-3/32 in. OD x 2-25/32 in. ID x 1/32 in. thick
- Factory replacement
- High quality
- Used on Armstrong S-25
- Fits on B and G 75 series
- Replaces B and G P04080
- Fits on B and G 100 series
- Fits on B and G 150 series
- Interchangeable with B and G
The "T" Style Blue Flame Log Lighter is CSA Certified. The "T" design places the unique mixing chamber in the center of the Log Lighter for connections to the center rear of the firebox. The Log Lighter pipes connect on both the left and right sides of the mixing chamber. The Blue Flame Steel Log Lighter is designed to help ignite wood in a fireplace. Eliminates the need for paper or kindling. This Log Lighter features steel construction for durability and the design of the air/gas mixing chamber makes lighting a wood fire safer than burning raw gas.
- Reduces emissions in the environment by 50% during use
- Shutter attached to the air or gas mixing chamber adjusts the flame from golden radiant to hot blue for a hotter fire
- Ignites even wet firewood
- Increases radiant heat in the room
The DELAVAN 0.65 70W Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type W-nozzles are neither truly hollow nor solid. These nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.40 and 8.00 GPH, regardless of the burners air pattern. The lower flow rates tend to be more solid. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.75 70B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
At the forefront of nozzle development, Delavan created its nozzle using bi-metal construction. The Brass body and stainless steel metering parts permit machining to close tolerances for precision and consistently high performance. Brass transmits heat fast from the nozzle face to reduce the possibility of varnish and oil residue buildup. Stainless steel provides that extra durability for metering parts where wear is a factor.
- Boiler replacement part
- For use with an oil-burning appliance
- Brass body
- Stainless-steel, hollow orifice
Character size 1/8"
- Steel dies
- Exclusive thumb grip
- Sharp characters for deep impression
- Wood box holder
- Pkg of 27
- Black
- Sharp engraved characters to ensure deep impression
- Features exclusive thumb grip for convenient handling
- Steel dies for durability and versatility
- Wooden box holder for keeping the letter stamps organized
All the features you trust from the original Isolator Uni-Flange ball valve, plus a 360 degree rotating flange that allows for orientation to any degree necessary for your installation. This forged brass full port ball valve features a blow-out proof stem, adjustable packing glands and a stainless steel snap ring for extra stability during installation. The only way to isolate circulator pumps.
- Conical inlet to minimize turbulence
- Replaces 3-components, eliminates 2-leak paths, saves approximately 20 minutes in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents electrolysis
- Eliminates galvanic corrosion
The DELAVAN 0.65 80B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.00 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified