Hard Start Kits
Hard start relay and start capacitor, gives additional starting torque up to 500%. For all single phase 120/288VAC units from 1/2 through 10 HP. 2 wire connection to existing run cap for easy installation. For severe Low-Voltage or hard starting compressors.
- Residential and commercial PSC A/C units and heat pumps
- Can be used on 120 thru 288 VAC units
- Room A/C units
- Installs in seconds across run capacitor terminals
Hardstart relay and start capacitor, gives additional starting torque up to 300% for all single phase 120/288 VAC units from 1/2 through 10 HP. 2 wire connection to existing run cap for easy installation. For low voltage and hard starting compressors.
- Residential and commercial PSC A/C units and heat pumps
- Can be used on 120 through 288 VAC units
- Room A/C units
- Installs in seconds across run capacitor terminals
Hard start kit 3-1/2, 4, 5
- High-quality steel housing for enhanced durability
- Conveniently holds water at a capacity of up to 19 gal.
- Efficiently operates at a maximum pressure of up to 100 PSI
- Electrostatically applied polyester paint resists corrosion
1.0 - 3.0 ton maximum torque Hard Start Device for single phase 208-Volt, 230-Volt and 265-Volt A/C, refrigeration and heat pump compressors. Hard start devices extend the life of compressors considerably by bringing them up to full speed more quickly and efficiently. They also assist compressors in starting under very adverse ambient conditions such as low voltage or high head pressures.
- 2-wire design for easy installation
- Extend the life of compressors
- OEM tested and approved
- 1-3 ton unit
The 5-2-1 compressor saver protects vital air conditioner components by significantly reducing the amount of time it takes for your compressor to start, in some cases up to 50%. This means that your air conditioner and compressor will bear half the stress, strain, and heat each and every time it starts. This compressor might save thousands of dollars by not having to replace the air conditioner.
- 3 wire hard start kit is pre-wired potential relay and start capacitor
- Reduces time compressor is on high amp start up, which helps prevent the dimming effect of household lighting
- Three color coded wires to connect for ease of installation Instant re-start
- For use on reciprocating and scroll compressors
Hard Start Kit Positive Temperature Coefficient (PTC) Relay and Start Capacitor SPP Series. PTC Positive Temperature Coefficient Relay and Capacitor. NATE Recognized (Course #1867-0002). Can be used on PSC type compressors.
- Easy 2-wire installation
- Increase in torque 600%
- Most economic
- UL recognized
2-wire potential relay and start capacitor. 3.5-5.0 ton maximum torque hard start device. Hard start devices extend the life of compressors considerably by bringing them up to full speed more quickly and efficiently. They also assist compressors in starting under very adverse ambient conditions such as low voltage or high head pressures.
- 2-wire design for easy installation
- Extend the life of compressors
- OEM tested and approved
- 3.5-5 ton units
110 VAC to 125VAC Solid-state Hardstart Relay, includes relay, overload and start capacitor. Used refrigeration systems with or without run capacitors. Rated for 1/4 HP to 1/3 HP compressors. Maximum RLA 6.8 Amps.
- Prevents low voltage starting problems
- Replaces relay, overload and provides a boost for hard start and unbalanced systems
- UL recognized
- Made in China
Hard starts relay and start capacitor combination, gives maximum torque possible for all single phase units from 1/12 through 10 HP. The simple 2 wire connection is Voltage sensing and has instant restart capability. A backup electronic timing circuit protects the compressor.
- Electronic potential relay (EPR) technology and 330 VAC start capacitor
- UL recognized file E146162
- Can be used on PSC and CSIR type compressors
- Voltage sensing 90V-277V
The 3-Series hard starts provide the service professional with an OEM option when the application calls for a hard start. Combining a potential relay and start capacitor the 3 series provides a TRUE 3 wire solution. Installation is convenient with the EZ snap bracket. The recommended range for the 3W2 is 4 to 5 HP.
- Mechanical potential relay
- Voltage sensing
- Instant re-start
- 35 Amp relay contacts
- 330 VAC capacitor
- UL recognized
MFG Part# 1053137
- Genuine OEM product
- Multiple applications (such as drain pans or anything driven by a size or dimension)
- For Gas Furnace Applications (pilots, flame sensors, etc.)
The 3-Series hard starts providing the service professional with an OEM option when the application calls for a hard start. Combining a potential relay and start capacitor the 3 series provides a true 3 wire solution. Installation is convenient with the EZ snap bracket. The recommended range for the 3W1 is 1 to 3 HP.
- Voltage sensing
- Instant re-start
- 35 Amp relay contacts
- 330 VAC capacitor
- UL recognized